Turner desk mic question

[Badge19]

Just picked up a Turner Super Sidekick, wired with a 4 pin connector. To use this mic on my Uniden Washington can I swap the 4pin for a 5pin or will I have to use a 4pin to 5pin adaptor

[sonoma]

you could try an adapter but some of the 5 pin radios will squeal using this set up. the 5 pin uses 2 grounds and works best with a 5 pin wired correctly. one ground goes to the audio ground wire on the mic plug and the other actually goes to board ground through the mic plug.
Turner
1- White
2- Shield
3- Black
4- Red
5- Blue
Yellow NC
here is what each wire does.
Stock
1- Audio
2- Shield
3- Receive
4- Sw Com
5- Transmit
this should be the layout for the plug for a turner as long as the mic cord has not been changed.
[Please login or register to view this link] Super Sidekick

[ Post made via Linux Laptop ]

[MDYoungblood]

The adapter is the cheapest way to go and it lets the mic be plugged into other radios as well. Here is a couple other ways of showing how to rewire the mic to work on radios like the Washington, this process is a little complicated but worth doing. Old Turner mics have great sound quality.

YOUTUBE_ADMIN

YOUTUBE_ADMIN

YOUTUBE_ADMIN

YOUTUBE_ADMIN

3's

Greg

[Badge19]

Thank you for the replies, great info. I'm currently going with the adaptor, so far so good; no squeal. Btw, I opened the 4pin connector and don't see the blue(common) wire; wondering if mic has been rewired.

[MDYoungblood]

Yes that is an old 4 wire microphone, only the new mics have 6 wires. The adapter uses a diode in the switching to compensate for the grounded shield.

3's

Greg

[CHOPPERDAVE]

I think the Turner Plus 3 B had the blue wire, I could be wrong.

[MDYoungblood]

I think the Turner Plus 3 B had the blue wire, I could be wrong.

The Turner "B" models were 6 wire mics. Wouldn't be a problem wiring them to any radio

3's

Greg

[Rabbit Ears]

Awesome, I had to make my own "pinball" type switches for my +3 and +2 mics. Doing the relay is really awesome.....and is a time-saver. You are RIGHT about the unavailability of the "open audio kits" that Turner once offered decades ago.

Thanks for the video... MDYoungblood!!

Respectfully and thankfully,
Rabbit Ears

[jon6667]

i just scored a mint turner +3 for 20 bucks. nice
one to add to my collection

[443 Arizona]

well who da thunk i would be lookin at turner guts at 3 am and get schooled.
thank you Greg.
if i actually get mine working now i'll be rattling the airwaves once again,AMPLIFIED

[CHOPPERDAVE]

I need a Push to talk bar for one of my plus 3's mine broke inside , tried repairing it but, both arms that hook under the plate were broke in a few different places.

[jon6667]

im presciently refurbishing a turner plus 3 . changing all the caps
it will be sweet when im done

[kf4eyr]

one thing to remember about the super side kicks is that there is a adjustment under the mike as well as the one one top,, i have seen a few people trying to wire it to their radios and complain it is bad but all it was just that the bottom needed to be turned down to match up with the radio,, with my first generation president washington the underneath is about half way and the top is half way and the radio is all the way,, every one says it is clear with lots of modulation,,,,

[443 Arizona]

well sticking with Turners, I want to put a long mic cord on one of mine, say 8 feet, not coiled.
where can i get some good cord?, need a 5 pin connector too.

[MDYoungblood]

well sticking with Turners, I want to put a long mic cord on one of mine, say 8 feet, not coiled.
where can i get some good cord?, need a 5 pin connector too.

I know CB World has the coiled cords but you might have a hard time finding straight cord, especially a cord with only one of the 6 conductors shielded. Looks like a deep internet search.

3's

Greg

[443 Arizona]

i would settle for a coiled cord and just straighten it with a heat gun, if i could only get Santa's little helpers to fix it all, haha