Ad blocker detected: Our website is made possible by displaying online advertisements to our visitors. Disable your ad blocker to continue using our website.
headphones
Just any other questions that you don't see a forum for? Go ahead and post here.
Post Reply
4 posts
• Page 1 of 1
-
- Mud-Duck Jr.
- Posts: 5
- Joined: December 13th, 2021, 2:30 pm
- Handle: Nicky
- Real Name: James
- Antenna: Sirio27
- Radio: Uniden 980, Anytone AT6666
- Contact:
headphones
Hello everyone,
I have been into CB about a year and have a question concerning headphones. I have a ANYtone 6666 and a Uniden 980. I have a hearing problem and speakers just don't get it for me. A good friend of mine gave me a set of vintage Archer[Radio Shack] 8 ohm Headphones that he rewired for mono as they were originally stereo. These work fantastic on The Anytone 6666 but not so good on the 980. The volume on the 980 is too high even on the low setting. Is there any way to install a volume control on the headphones just for use on the 980. By the way I found another set on EBAY and just want to set them up for the 980.
Any help is greatly appreciated, thanks in advance
Nicky1
I have been into CB about a year and have a question concerning headphones. I have a ANYtone 6666 and a Uniden 980. I have a hearing problem and speakers just don't get it for me. A good friend of mine gave me a set of vintage Archer[Radio Shack] 8 ohm Headphones that he rewired for mono as they were originally stereo. These work fantastic on The Anytone 6666 but not so good on the 980. The volume on the 980 is too high even on the low setting. Is there any way to install a volume control on the headphones just for use on the 980. By the way I found another set on EBAY and just want to set them up for the 980.
Any help is greatly appreciated, thanks in advance
Nicky1
- TNT1450
- Duckplucker
- Posts: 185
- Joined: October 28th, 2018, 6:15 pm
- Handle: Cobra Ball
- Real Name: Tom
- Radio: Pace 8046, Roadtalker 40's, Teaberry Stalker IX, GE 3-5814A
- Contact:
Re: headphones
Yes, maybe install a potentiometer, say about a 10K or 50K, in one side of the headphones and run the audio in to that, then over to the other side for the other ear. Make sure you get an audio taper pot (A) instead of a linear taper pot (B). Or, you could install a resistor at the headphone jack on the Uniden 980 to tame it down a bit. But having a volume control on the headphones would be handy.
- Bozo
- Owner
- Posts: 9414
- Joined: August 31st, 2004, 1:06 pm
- Handle: Bozo The Clown
- Real Name: James Wadsworth
- Antenna: Monkey Made MM9
- Radio: General Lee Radio
- Contact:
Re: headphones
Hey @nicky11nicky1 wrote: ↑September 10th, 2023, 11:05 am Hello everyone,
I have been into CB about a year and have a question concerning headphones. I have a ANYtone 6666 and a Uniden 980. I have a hearing problem and speakers just don't get it for me. A good friend of mine gave me a set of vintage Archer[Radio Shack] 8 ohm Headphones that he rewired for mono as they were originally stereo. These work fantastic on The Anytone 6666 but not so good on the 980. The volume on the 980 is too high even on the low setting. Is there any way to install a volume control on the headphones just for use on the 980. By the way I found another set on EBAY and just want to set them up for the 980.
Any help is greatly appreciated, thanks in advance
Nicky1
Step 1: Get your vintage Archer headphones and some materials.
Step 2: Open a small box and make a hole in it.
Step 3: Cut the headphone wires .
Step 4: Connect one wire to one side of a knob and another wire to the middle of the knob.
Step 5: Attach a wire from the other side of the knob to the remaining headphone wire.
Step 6: Put the knob in the hole on the box.
Step 7: Close the box . Step 8: Plug your headphones into your Uniden 980 CB radio .
Step 9: Start with the knob low and turn it up slowly until it's the right volume for you.
Now you have control over your headphone volume with a cool knob!
-
- Mud-Duck Jr.
- Posts: 5
- Joined: December 13th, 2021, 2:30 pm
- Handle: Nicky
- Real Name: James
- Antenna: Sirio27
- Radio: Uniden 980, Anytone AT6666
- Contact:
Post Reply
4 posts
• Page 1 of 1
Jump to
- Welcome and Community
- Skip Shooter's Paradise
- ↳ General Discussions
- ↳ Watergates & Videogates
- ↳ Shooting Skip
- ↳ Hall Of Fame
- ↳ Journal
- Radio Help
- ↳ Intro To Radios 101
- ↳ General Questions
- ↳ Base Setups
- ↳ Mobile 🚗 / 🏠 Base Install Help
- ↳ Competition Rigs
- ↳ Amplifiers / Power Supplies
- ↳ Charging System
- ↳ Mobile Setups
- ↳ Antenna Help
- ↳ Microphone Info
- ↳ Radio Modifications
- ↳ Shortwave Radios / Scanners
- ↳ Sideband (SSB)
- ↳ Tube Radio Equipment
- ↳ Other Technical Questions
- ↳ Miscellaneous Radio
- Buy / Sell / Trade
- ↳ For Sale Area Rules
- ↳ For Sale Area
- ↳ eBay Shopping
- ↳ Amazon Shopping
- ↳ Trade Equipment
- ↳ Wanted Radio Equipment
- ↳ Positive Feedback
- Off Topic
- ↳ Miscellaneous Chat
- ↳ Computer Help
- ↳ Signature Test Area
- The White House
- ↳ Ask Marv
- Federal Communications Commision (FCC)
- ↳ F.C.C. Rules And Regulations
Cbrt left panel
'CBRT' right panel
- Home
- All times are UTC-06:00
- Cookie-Settings
- Delete cookies
- About us
- Downloads
- Contact us
Maxthon style by Culprit. Updated for phpBB3.3 by Ian Bradley
Powered by phpBB® Forum Software © phpBB Limited
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.
⇧
⇩